Teledyne FLIR F-Series Small Pole Adapter
$189.00- For pole diameters between 65mm-110mm
Showing 61–80 of 92 results
-
-
-
-
Teledyne FLIR FC Series Pole Adapter
$159.00FLIR FC Series Pole Adapter
4132982
The FC-Series Wall Mount can be fixed to a Pole with this Pole Mount Accessory.
If the camera is mounted on a pole, an Ethernet cable should run at least to the bottom of the pole, so a laptop could be temporarily connected directly to the camera.
-
Teledyne FLIR IR Windows
- Reduces the need to open cabinets for inspections
- May reduce the need for layers of heavy protective gear*
- Easy to install
- Shortens inspection time
- Cuts the cost of inspections
*Personal protective equipment (PPE) may still be required as determined by your plant safety personnel.
-
Teledyne FLIR Large Pole Adapter
$309.00PT-Series & F-Series Wall Mount
High capacity pole mount for pole diameters between 150mm-230mm
Part Number 500-1116-00Kit Contents:
- PT-Series pole mount adapter 4119498
- Support strut pole mount adapter 4123212
- 4 each 5/16 nut
- 4 each 5/16 flat washer
- 4 each 5/16 split lock washer
- 3 each 1/4 nut
- 3 each 1/4 flat washer
- 3 each 1/4 split lock washer
-
Teledyne FLIR Neutrino LC Development Kit
$1,803.00Provides all output options on a single PCB and easy access to the full 80-pin camera interface for development.
Includes a flex cable between the board and the camera and a wire harness to the cooler interface. -
Teledyne FLIR Neutrino LC USB VPC Kit
$193.00The USB Video Power Connector (VPC) kit turns the Neutrino LC camera into a webcam. Power, digital video, and comm are all via USB2. The kit includes a USB-A to USB-C cable.
-
Teledyne FLIR Pole Junction Box for FB-Series Thermal Cameras
$174.00Pole Junction Box Pole Junction Box for FB-Series Thermal Security Cameras. Allows the FLIR FB Series O and FB Series ID cameras to be mounted on a Pole
-
Teledyne FLIR PT-Series Corner Mount
$269.00Teledyne FLIR PT-Series Corner Mount High capacity corner mount
Part Number: 500-1118-00
-
Teledyne FLIR PT-Series Pedestal Mount Assembly
$569.00Kit Contents:
- PT-Series pedestal mount 4119497 PT-Series adapter plate 4119468
- 6 each 1/4-20 FHMS x 3/4″Hex, S.S. 6 each 5/16-18 x 3/4 SHCS, S.S.
- 6 each 5/16 split washer
- 6 each 5/16 flat washer
- Two extra pieces of each attaching part
-
Teledyne FLIR PT-Series Small Pole Adapter
$389.00- High capacity pole mount for pole diameters between 80mm-150mm
-
Teledyne FLIR PT-Series Wall Mount
$729.00High capacity wall mount
The Teledyne FLIR PT-Series wall mount assembly is designed for use with medium- and heavy-duty pan and tilt units. -
Teledyne FLIR PTU-5 Side Mount Payload Bracket
$48.00Side Mount Payload Bracket (1)
Side-mounting payload bracket for the PTU-5 pan tilt. Up to 3 lb capacity per side, 6 lb total with two side brackets. Side bracket use requires removal of the PTU-5 top bracket. (Side and top brackets cannot be used together at the same time.) -
Teledyne FLIR Tau NFOV Lens Holder
$58.00Teledyne FLIR NFOV Lens Holder for the FLIR TAU 2 Thermal Cameras
-
Teledyne FLIR Tau PCB Wearsaver with Solder Pads
$136.00FLIR Tau PCB Wearsaver with Solder Pads A low-profile adapter that attaches to the Tau’s 50-pin Hirose connector, furnishing a solder pad interface. Schematic included. The Tau2 Wearsaver was designed to be an internal engineering/manufacturing calibration accessory, rather than an OEM interface. There is a Hirose mating connector on one side of the board, as…
-
Teledyne FLIR Tau Photon Replicator Board
$165.00This expansion board adapts the Tau camera’s native 50-pin Hirose connector to the 30-pin SAMTEC connector used on FLIR’s Photon cameras. The replicator board makes the Tau camera electrically pin-compatible to a Photon camera. Without a Photon Replicator Board, the input voltage range is 4.0-6.0 VDC for a Tau 320 camera, and 4.4-6.0 VDC for a Tau 640. With the Photon Replicator Board, the input voltage range is modified to 6.5-27.0 VDC.
* Includes spacer and screws
This expansion board adapts the Tau camera’s native 50-pin Hirose connector to the 30-pin SAMTEC connector used on FLIR’s Photon cameras. The replicator board makes the Tau camera electrically pin-compatible to a Photon camera.
Without a Photon Replicator Board, the input voltage range is 4.0-6.0 VDC for a Tau 320 camera, and 4.4-6.0 VDC for a Tau 640. With the Photon Replicator Board, the input voltage range is modified to 6.5-27.0 VDC.
A cast magnesium spacer and 4 socket-head machine screws are included (not shown).
Stock is very limited. There are only: 2 Units Left
-
Teledyne FLIR TAU WFOV Lens Focus Tool
$70.00The Tau Focus Tool can be used to change the focus of the wide field of view (WFOV) 5.5mm, 7.5mm, 9mm, 13mm, or 19mm lenses.
-
Teledyne FLIR Tau WFOV Lens Locking Ring
$24.00The lens locking ring is designed to mount a Tau WFOV camera into a bulkhead. The M29 x 1.0 thread on the outside of the lens mount flange is placed through the clearance hole in the bulkhead and the O-ring seals the camera to the face. The Type 2-025 O-ring is not for sale through…
-
Teledyne FLIR Tau WFOV Lens Mount – Locking Ring Install / Removal Tool
$82.00The lock nut tool will attach to a torque wrench for proper tightening of the lens locking ring. Torque the locking ring to 4.0 in-lbs.